<div dir="ltr">Dear Fang-Yu,<div><br></div><div>You save .set, 1-Hz high-pass, run ICA, apply the ICA weight matrix to the .set to obtain un-highpassfiltered results. This is an old trick once recommended by Stefan Debener in SCCN. Then you may want to apply high-pass with very low cut-off. Follow Andreas's recommendation:</div><div><br></div><div><span style="font-size:12.8000001907349px">> Thus, high-pass cutoff frequency should not be higher than 0.03 Hz.</span><br></div><div><br></div><div>Makoto</div><div class="gmail_extra"><br><div class="gmail_quote">On Mon, Nov 23, 2015 at 11:44 PM, Fang-Yu Chang <span dir="ltr"><<a href="mailto:hardheard101@gmail.com" target="_blank">hardheard101@gmail.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left-width:1px;border-left-color:rgb(204,204,204);border-left-style:solid;padding-left:1ex"><div dir="ltr">Dear eeglablists<br><div class="gmail_quote"><div dir="ltr"><div><br></div><div>I would like to analyze the bereitschaftpotential (BP), and I have 2 questions which are related to set the filter's condition.</div><div><br></div><div>First, I set high-pass filter at 1 Hz and low-pass filter at 30 Hz. After running ica, there  was 30 Hz amplitude in every independent component (IC). However, high-pass filter at 1 Hz and low-pass at 70 Hz were set, and there was no amplitude in every IC. I would like to ask how did it happen?</div><div><br></div><div>Second, I noticed that there is a difference between setting high-pass filter at 0.1 Hz and setting high-pass filter at 1 Hz. If high-pass was set at 0.1 Hz, the amplitude of the peak was about 27 microVolts, but if high-pass filter was set at 1 Hz, the amplitude of the peak was about 5 microVolts. My vice mentor speculates that BP is a kind of slow wave, so it's reasonable that we set high-pass filter at 0.1Hz. Nevertheless, we would like to ask experts' opinions. According to previous studies, the amplitude of BP is about 10 microVolts in the healthy adults.</div><div><br></div><div>The pictures for low-pass filters were set at 70 Hz and 30 Hz separately.</div><div>Low-pass filter at 70 Hz  </div><div><a href="http://imgur.com/L5tAxx6" target="_blank">http://imgur.com/L5tAxx6</a><br></div><div><br></div><div>Low-pass filter at 30 Hz </div><div> <a href="http://imgur.com/5SwNDZv" target="_blank">http://imgur.com/5SwNDZv</a><br></div><div><br></div><div>In addition, here is my system information: Matlab is 2014a and eeglab is 13.5.4b.</div><div>Thank you.</div><div><br></div><div>Sincerely,</div><div><br><div>Stella Ling</div></div></div>
</div><br></div>
<br>_______________________________________________<br>
Eeglablist page: <a href="http://sccn.ucsd.edu/eeglab/eeglabmail.html" rel="noreferrer" target="_blank">http://sccn.ucsd.edu/eeglab/eeglabmail.html</a><br>
To unsubscribe, send an empty email to <a href="mailto:eeglablist-unsubscribe@sccn.ucsd.edu">eeglablist-unsubscribe@sccn.ucsd.edu</a><br>
For digest mode, send an email with the subject "set digest mime" to <a href="mailto:eeglablist-request@sccn.ucsd.edu">eeglablist-request@sccn.ucsd.edu</a><br></blockquote></div><br><br clear="all"><div><br></div>-- <br><div class="gmail_signature"><div dir="ltr">Makoto Miyakoshi<br>Swartz Center for Computational Neuroscience<br>Institute for Neural Computation, University of California San Diego<br></div></div>
</div></div>