<div dir="ltr">Hi Everyone,<div><br></div><div>I am having a few issues with getting the quik-cap 128 sensor locations to work in EEGLab. Here is a list of the things I have tried.</div><div><br></div><div>(here is the .cnt file from myself in case anyone wants to follow along with my issue</div><div><a href="https://drive.google.com/open?id=0B0EVinjrroSQWFJsVjVTdWpkRXc">https://drive.google.com/open?id=0B0EVinjrroSQWFJsVjVTdWpkRXc</a>).<br></div><div><br></div><div>1. Since the 128 channel quik-cap uses the 10-5 system I initially used the standard-10-5-cap385.elp file. This was able to find the positions of 'most' of the channels. This is the image of the 2-d plot (<a href="https://drive.google.com/open?id=0B0EVinjrroSQZVl4aWVmaWZpQUU">https://drive.google.com/open?id=0B0EVinjrroSQZVl4aWVmaWZpQUU</a>) However, TPP5h, P11, PO11, POO11h, POO12h, PO12, and P12 did not have locations. </div><div><br></div><div>2. As a result, I contacted Neuroscan for their channel locations and received this file (<a href="https://drive.google.com/open?id=0B0EVinjrroSQUjBYckVNU0swSW8">https://drive.google.com/open?id=0B0EVinjrroSQUjBYckVNU0swSW8</a>). However, this file was not supported by EEGLab so instead I extracted the XYZ coordinates and created a .ced file and imported those locations (<a href="https://drive.google.com/open?id=0B0EVinjrroSQUVBjel84eWNYVWs">https://drive.google.com/open?id=0B0EVinjrroSQUVBjel84eWNYVWs</a>). Because of axis differences I switched to "Nose along +Y" to correct axis differences. The 3-D image looks correct (<a href="https://drive.google.com/open?id=0B0EVinjrroSQNHY5UVNFeGxaRW8">https://drive.google.com/open?id=0B0EVinjrroSQNHY5UVNFeGxaRW8</a>) but when I look at the 2-d plot this is what I see (<a href="https://drive.google.com/open?id=0B0EVinjrroSQT2ljd1l2ODBOeEE">https://drive.google.com/open?id=0B0EVinjrroSQT2ljd1l2ODBOeEE</a>). I attempted to adjust the positioning using the 'Opt. head center' and have tried both the 'Optimize center location' and 'specify center' with the coordinates of Cz and I have ignored channels that have no channel locations. But when I use optimize center location, nothing changes and when I use the Cz coordinates I end up with this (<a href="https://drive.google.com/open?id=0B0EVinjrroSQZVl4aWVmaWZpQUU">https://drive.google.com/open?id=0B0EVinjrroSQZVl4aWVmaWZpQUU</a>).</div><div><br></div><div>3. The last thing I attempted, after loading the .ced file and correcting the +Y axis as to 'Rotate Axis' - X (rotate X-Z plane) CZ. Which did not seem to make a difference either.</div><div><br></div><div>Any suggestions would be appreciated to figure out how to get the channel positions to fit the 2-d headplot.</div><div><br></div><div>Thanks,</div><div>Daniel</div></div>